S3850 UPLOAD DATA TO PC PROBLEM

THIS IS HOW I SOLVE IT:

1: Download this file (all needed file inside) and this SAMSUNG USB DRIVER

2: Open DOWNLOADER and set it up just like this:

3: Set s3850 in download mode
3a: Pull out battery
3b: Put battery in
3c: Press CALL,VOL+ and power until screen in the phone show DOWNLOAD

4: Take microusb and connect to the phone and pc.

5: DOWNLOAD button on the DOWNLOADER.EXE will be clickable

6: Just click that button and wait...

7: NEVER TOUCH YOUR PHONE UNTIL YOUR PHONE RESTART BY ITSELF (THIS PROCCESS CAN TAKE UP TO 15MINUTES)

8: Done!!

if you guys want to!! :D 

PROBLEM WITH DGPU ACER 4820TG

Hi everyone!!

Today i want to tell with you all my experience with 4820TG...

Begin of story, After finish with reinstall window and install all needed driver i restart that laptop and after wait about 10 minutes the screen still in blank then i suspect this must be graphic  card problem..

Shutdown the laptop with proper step (WIN KEY, RIGHT ARROW, ENTER), then turn on it back to go the bios with F2 then i change "display mode" from "hybrid to dGPU" with the hope that something miracle happen  and press F10 then Enter to save it...

After i did that step, the laptop  refuse to turn on...  i feel very strange and feel uncomfortable because my customer send it with good condition (can turn on)..

I've tried all step that i know  to reset BIOS to default:
1: pull out battery and charger then press power button 30 sec
2: pull out CMOS battery in the motherboard for 6hour
3: flash BIOS
but nothing can fix that..

After some research, i found that laptop cant turn on if "discrete GPU" also known as dGPU failed. dGPU is graphic card like NVIDIA, ATI, MSI and etc... Lucky for me because i know this model come with 2 GPU, haha.. All latest intel processor like P6100, i3, i5, i7 come with intel HD GPU inside..

So,  this is how i fix it,

1: Download Modded BIOS that use intel HD as default GPU in HERE
2: Pull out all power recources to the computer, USB, CD and internet cable..
3: Extract and Put downloaded Modded BIOS (ZQ1x64.fd)  to EMPTY USB DRIVE formatted with FAT32...
4: Put than USB DRIVE to the USB SLOT in laptop..
5: HOLD fn+esc while power it on until power LED blink then release fn+esc button..
6: Wait about 5-10 minutes or until the laptop restart itself..Remember, screen will remain in blank at this step.
7: Your laptop now should be can ON like before
8: Horreyyyyyyy!!!

Sorry for bad english, and do it on your own risk... hehe...

Thanks for reading my experience with this 4820TG...

Setup WDS Dlink 2750U with 2640B

ok, this is what i do...

get ready with your router..

ROUTER A (main router DSL 2750U) ROUTER B (Bridge router DSL 2640B)

1: Login to your router then go to http://192.168.1.1/wlwds.cmd and choose "Acess Point" at AP Mode and "Disabled"
at Bridge Restrict, and click Aplly/Save..

2: Go to this http://192.168.1.1/lan.html and Enable DHCP Server
and set DHCP IP Address Range between 192.168.1.9 to 192.168.1.255 and click Aplly..

3: Then go to this http://192.168.1.1/wlcfg.html and choose your wifi channel EG: 6
Then Write all this information from your router A...
Wireless name
Security key and type
Wifi channel number EG: 6

4: Logout your router A and and prepare your router B..

5: Take a LAN cable then connect it to your router B and your computer
(IMPORTAN: disconnect your connection with roter A)

6: Power ON your router B and reset it...

7: SET STATIC IP in your computer for your LAN connection. EG: 192.168.1.22

8: Login to ROUTER B and Go to this http://192.168.1.1/lan.html and in Router IP Address fill it with
192.168.1.2 and Disable DHCP Server and click apply..

9: Login to your router B via 192.168.1.2 and login then
Set your wifi security key and type same as ROUTER A in this address http://192.168.1.2/wlsecurity.html

10: Set your Wifi name and channel number same as your ROUTER A in this address http://192.168.1.2/wlcfg.html..

11: go to http://192.168.1.2/wlwds.cmd and choose "Acess Point" at AP Mode and "Enabled/scan"
at Bridge Restrict.. wait about 15 sec then tick Your SSID and BSSID in remote bridge MAC Address..

12: Remove your Static IP for your LAN connection that we make in step 6 early..

13: Restart Your Router B and wait for 2 minutes..

14: At this step, you should be able to access Router A at 192.168.1.1,router B at 192.168.1.2
ans surf the internet...

15: If all works fine, unplug your lan cable and we have Done!

Use DLINK DSL 2750U as Network Storage

Hi, today my beloved 7 years laptop broken and i decide to put it in my sparepart collection...
When i disassemble it, i took the hardisk and decide to use it as my network storage in my dsl 2750u..

this is how i do it:
1: put your hardisk in usb port at your dsl 2750u
2: log in to your router and go to ADVANCE/STORAGE DEVICE/STORAGE DEVICE INFO to make sure your hardisk readable..
 

3: Make a username in ADVANCE/STORAGE DEVICE/USER ACCOUNT and create your username/password by click ADD and insert desire username, password and repeat your password..
 

4: Log out your router and go to 'my computer folder' and type \\{your router ip} just like this
eg: my router ip is \\4.3.2.1
  
*common mistake: dont use /, but use \

5: hit enter and you will be prompt with network password, just fill it with your username and password that you created in your router in step 2 and if it ok you now can see your hard disk content just like this:
 
Done.. good luck!!

you can also use your pendrive, card reader!

UNBRICK DSL-2750U PART 3

Continued from part 2

Eight: Click Open at PUTTY (blank screen will appear), and switch on the router then see if you can get any information from putty just like this: Switch off router and get ready for tricky part..
Note: if you cant see anything, just change RX and TX wire in step three at part 1 then restart this process..

Nine: Switch ON the router and hitting ctrl+C quickly until you see this CFE screen:
if cant get to there, just keep trying..

Ten: When you can get int CFE screen, Type: e nvram and hit enter then hit y (make sure CAPSLOCK OFF).
Ten: Go to IE and type 192.168.1.1 in address bar and you should see this page:
Update your firmware with this version EN1.01 (more stable than TH1.01) Or just switch OFF your router and switch ON back to use default firMware GE1.00..


MORE PICTURE IN HERE
Thanks..

UNBRICK DLINK DSL-4750U PART 2

Continued from part 1

Five: Open device manager, and right click at prolific serial usb (please remember it com port) then pick properties and fill it just like picture below..
 

Click OK

 Six: Download PUTTY (in here) and open it then go to to the serial (left side) and fill it just like this: ok now click session (left side) then fill it just like this: Remember, dont click OPEN yet!


Seven: Go to Open Network And Sharing Center, change adapter setting (left side), right click at LOCAL AREA CONNECTION and pick properties, double click at INTERNET PROTOCOL VERSION 4 and fill it just like this:

Continue to part 3 in here

UNBRICK MY LINK 2750U AFTER A BAD FIRMWARE FLASH

Hi, last week my router (DSL-2750U) bricked because i had downgrade that router from TH1.01 to SE1.00.. So today i gonna show you all how to unbrick your dlink dsl-2750u if you have made a same mistake with me..

First and most important part,make sure your router BRICKED..
Below is the picture of my bricked router: (power LED dimmer than usual)
 

Two: Made a simple SERIAL CABLE from NOKIA DKU5 or CA42 cable like this:
*remember, we only need 3 wire.. GND, RX and TX..

Three: Connect all 3 wire that we made from above picture to the router just like this:

Four: Install Prolific driver <in here> then Connect rj45 cable to the LAN port and computer,switch on plug then connect Power cable to the router (switch off the switch at router) and connect your DIY SEIAL CABLE to the computer..
just like this:
 
continue to part 2 in here